Special extrusion

Box extrusion 50x120
type A01-6

This extrusion is mainly used as a cable duct . The front side can be edited without any problem for the installation of plugs, switches and other equipment. The finish on the rear side is made with a screwed on or pushed in aluminum sheet.

Hand rail extrusion 50x50
type A19-1

Hand rail extrusion of stairway-hand-rails or with providing gates.

Wall rail 50x18
type A19-9

A extrusion, which lays flat on. Fastened with pegs to walls, clipboard holders can be fastened very simply, with height adjustment to this profiled rail.

Slot extrusion 20x80
type C08-2

As base plate or transition profile 80 x 80/40 x 80 to 40 x 80/40 x 40-extrusion, and/or to mount customized components.

Slot extrusion 20x120
type C08-3

As base plate or transition profile 80 x 80/40 x 80 to 40 x 80/40 x 40-extrusion, and/or to mount customized components.

triple channel  extrusion 50x15
type A05-1

An extension extrusion with best suitability for insulation, glazings and sliding doors - so everywhere, where aesthetics and functionality are in demand. The sliding extrusion can be fixed to each construction extrusion of the basis 50mm. Plastic extrusions can be used for the improvement of the sliding quality or as slot reduction or covering section.

Triple channel extrusion 30x15
type B05-1

The sliding extrusion for the basis 30mm. The plastic extrusion B39-55 or B39-35 can be used for the improvement of the sliding quality, for slot reduction or covering section.

19"-auxiliary extrusion
type A05-2

The attachable auxiliary extrusion makes the admission of 19"-inserts within the ranges for electronics, pneumatics and hydraulics. This special perforated rail can be screwed onto each construction extrusion of the basis 50mm. In the correct distance installed, it fulfills the requirements of the 19"-technic. Suitable threaded inserts with retaining spring facilitate the extension of the modules.

19"-auxiliary extrusion
type B05-2

This special perforated rail can be screwed onto each construction extrusion of the basis 30mm, similar to the upper extrusion. 19"-Racks.

Base extrusion 30x30
type B01-1

In the trade fair construction and shop fitting this extrusion has been successfully used for years. Thanks to the unusual stability it's used mainly as vertical supporting extrusion. A special advantage is in the fact that the center with the diameter of 8.3 mm permits a direct cutting of M10-threads and this again makes the admission of placing leveling feet and castors easily without accessories.

Triangular support extrusion 30x120°
type B01-4

In the trade fair construction and shop fitting this extrusion has been successfully used for years. Thanks to the unusual stability it's used mainly as vertical supporting extrusion. A special advantage is in the fact that the center with the diameter of 8.3 mm permits a direct cutting of M10-threads and this again makes the admission of placing leveling feet and castors easily without accessories.

Angle extrusion 30x30
type B19-3

This extrusion you slide-in the construction extrusion of the basis 30 for simple stanting constructions.

Runner extrusion 30x30
type B10-3

Raw material for the single and double run cars. In addition, can be used as frame extrusion for the admission of thick panels.

Runner extrusion 30x50
type B10-9

Raw material for the single and double run cars. In addition, can be used as frame extrusion for the admission of thick panels.

Surround extrusion 30x15
type B05-7

With this extrusion become panel finishes a graceful design.Different material thicknesses can become balanced with the PVC clamping extrusion B39-45.

U-clamping extrusion 8x13.5
type B19-6

Special extrusion for clamping the fences. The extrusion fits into all extrusions of the basis 50, 40 and 30.

Support extrusion 11x30.5
type B19-7

The support extrusion is hooked into the 8mm-slot of the construction extrusions and serves as a support of table tops, clipboards, panels etc.

Clamping extrusion 16x29
type A05-6 

A brilliant extrusion for the attachment of all kinds of panels. It can be attached additional into all 8mm-slots of the extrusions base 50 and 40mm. Panels can be used or replaced in a simple way, this without dismantling the main construction!

Double clamping extrusion 16x50
type A05-7

A brilliant extrusion for the attachment of all kinds of panels. It can be attached additional into all 8mm-slots of the extrusions base 50 and 40mm. Panels can be used or replaced in a simple way, this without dismantling the main construction!